- #Dvdx wii 4.3u download install#
- #Dvdx wii 4.3u download update#
- #Dvdx wii 4.3u download Pc#
- #Dvdx wii 4.3u download download#
Lego Indiana Jones - Indiana PWNS (4.3U 4.3E & 4.3J)ġ. *You may need to try this many, many times for it to work* *You need to delete all custom stages for this to work* (This may take several tries before it loads) LoadMii starts, load from SD Card - Press AĦ. Insert SD Card, Go back to stage builderĥ. Go to Vault then Stage Builder, delete all custom stages, exit stage builderĤ. Load Super Smash Bros Brawl, wtih SD Card removed, make a save fileģ. If you have a Super Smash Bros Brawl savegame, back it up and delete from wiiĢ. Super Smash Bros Brawl - Smash Stack (4.3U)ġ. Extract with WinRar (Download is on top of the page) This guide works, but the process is not noob friendly. You may or may not need a Gamecube controller (Zelda Twilight Princess won't work for this) Super Smash Bros Brawl or Lego Indiana Jones It is not recommended to restore your NAND if you have Bootmii installed as an IOS. If ever you get bricked, then copy the bootmii folder and NAND backup onto your card and do steps 1 and 2 again use Preloader to get to HBC if necessary, then select the icon with the arrow going from the SD card to the chip.
#Dvdx wii 4.3u download Pc#
If you installed Bootmii as boot2 then also copy the Bootmii folder to your PC and either delete or rename it, otherwise it will load every time you switch your Wii on. If those buttons don't work then you will have to use a Gamecube controller.ģ) Now select the icon with a green arrow pointing from the chip to the SD card and follow the on screen instructions.Ĥ) In about 10 minutes you will have a NAND backup, it is normal to have up to 80 bad blocks so don't worry if you get some.ĥ) Put the SD card into PC and copy the NAND backup somewhere safe, you can now delete it from your card. Try to use a Sandisk or a similar brand.ġ) Put the SD card into the Wii, if you installed Bootmii as boot2 then it will load, if it is installed as an IOS go to the Homebrew Channel, press 'home' on your wiimote and select 'Launch Bootmii'.Ģ) Use the power/reset/eject buttons to navigate the Bootmii menu and select the icon with the gears on it.
#Dvdx wii 4.3u download install#
Use the same SD card you used to install Bootmii and make sure there is at least 530mb free on it.īootmii is very fussy about what SD cards it uses, so avoid generic ones. There is a 00.1% chance that it will happen. Making a NAND backup with Bootmii is highly recommended, as it will recover your Wii from 99.9% of bricks unless you smash your Wii with a brick. If you were able to install BootMii to boot2, then follow the steps in Backup Your NAND. For most of you, it will be installed as an IOS. Note: In most cases, BootMii will give you an error, so it cannot be installed as a boot2.
After it finishes, install it as boot2 (if possible) or as an IOS. *Optional* On bootmii option, select "prepareSD card". BootMii installation is optional but recommended for people who value their Wii so it doesn't brick. A disclaimer will appear, press "1" to continue.ģ) Now three lines should appear: Homebrew channel, which can be installed, DVDx, also can be installed, Bootmii, which possibly will give you an error. If you encounter a problem with your Wii freezing then reset your Wii and click Options, then Data Management, then Channels, then click the SD tab. A disclaimer will appear, press "1" to continue. Once you do this, a warning screen about scams should appear, press OK. In the root of the SD card you should have:Ģ) Run to your Wii, place the card in the SD slot, and navigate to the SD card icon on the bottom left.
#Dvdx wii 4.3u download download#
You can find your Wii Firmware version by going Wii settings.ġ) Open the contents from the download into the root of your SD card. INSTALLING HOMEBREW CHANNEL FOR 4.1 & 4.2ĭownload the package for your Wii Firmware. This will let you open packages I give you. You will also need a program installed into your computer called WinRAR. The only thing that you will need is an empty SD card formatted as FAT32.
The USB loader will still work though so just follow the guide as normal. The chipset is known as a D3-2 and the only way of telling if you have one is to open her up, but as this will invalidate your warranty you are better off trying to load DVDRs and if you just keep getting errors then it is a good indication that you have one. If your Wii came with system menu 4.0 on it, then it could be one. There is a new DVD drive chipset that is starting to emerge that will not play DVDR.
#Dvdx wii 4.3u download update#
Warning - All users who are on a firmware lower than 4.2, DO NOT update if you have a hacked firmware!! This will work on SYSTEM MENU 4.3, 4.2, 4.1 and under. You can virtually do almost about everything. Except everything about JTAGGING is 10x much easier on the Wii.
Note: For those XBOX users, modding your Wii is "jtagging".